- CAN bus speed?
- What does Lin mean?
- Can vs LS HS?
- Can Lin FlexRay Ethernet?
- What is K line and L line?
- How does a LIN bus work?
- What does LIN bus mean?
- What does CAN bus mean?
- What is the difference between can and FlexRay?
- CAN bus cable specs?
- What is difference between CAN and LIN?
- How does CAN bus work?
- Is Lin a word?
- How is CAN bus load calculated?
- What is Lin used for?
- Where is the can bus located?
- How does CAN bus wiring work?
CAN bus speed?
1 Mbit/secondThe maximum speed of a CAN bus, according to the standard, is 1 Mbit/second.
Some CAN controllers will nevertheless handle higher speeds than 1Mbit/s and may be considered for special applications.
Low-speed CAN (ISO 11898-3, see above) can go up to 125 kbit/s..
What does Lin mean?
LINAcronymDefinitionLINLingLINLocal Interconnect Network (automotive networking technology)LINLiquid NitrogenLINMilan, Italy – Linate (Airport Code)20 more rows
Can vs LS HS?
HS stands for “High Speed” CAN, “LS” stands for “Low Speed” CAN, and “SWC” stand for Single Wire Channel CAN. The majority of current applications use HS – High Speed CAN. For more details on these different types of CAN networks, see Slide 6 of the CAN Protocol Tutorial which discusses the Physical Layers.
Can Lin FlexRay Ethernet?
These always focus on special requirements, ranging from inexpensive implementation (e.g. LIN) through high bandwidth (Ethernet) to possible use in security-relevant distributed closed-loop control (FlexRay).
What is K line and L line?
The K-Line is suitable for both on-board and off- board diagnostics. K-Line is a bidirectional line. … Line-L is a unidirectional line and used only during initialization to convey address information from the diagnostic tester to vehicle ECUs, simultaneously with the K line.
How does a LIN bus work?
How does LIN bus work? LIN communication at its core is relatively simple: A master node loops through each of the slave nodes, sending a request for information – and each slave responds with data when polled. The data bytes contain LIN bus signals (in raw form).
What does LIN bus mean?
Local Interconnect NetworkThe Local Interconnect Network (LIN®), ISO17897, is a multipoint, low-cost, easily-implemented communication bus in automobiles, working as a sub-bus for the Controller Area Network in most applications.
What does CAN bus mean?
Controller Area NetworkA Controller Area Network (CAN bus) is a robust vehicle bus standard designed to allow microcontrollers and devices to communicate with each other’s applications without a host computer.
What is the difference between can and FlexRay?
The improved CAN FD standard allows increasing the bit rate after arbitration and can increase the speed of the data section by a factor of up to eight of the arbitration bit rate. FlexRay is an automotive network communications protocol developed through the FlexRay Consortium to govern on-board automotive computing.
CAN bus cable specs?
CAN Bus CableVoltage Rating:300VFixed:-40°C to +80°CFlexing:-30°C to +70°CNominal Impedance:100-120 OhmsBending Radius:15 x cable diameter2 more rows
What is difference between CAN and LIN?
Depending on the speed and cost requirements, either CAN or LIN can be implemented. … On the one hand, CAN serves high-speed, error-sensitive needs and operates on a 5-V differential bus. LIN, however, serves low-speed, low-bandwidth requirements on a 12-V single-wire bus.
How does CAN bus work?
The CAN bus system enables each ECU to communicate with all other ECUs – without complex dedicated wiring. … The broadcasted data is accepted by all other ECUs on the CAN network – and each ECU can then check the data and decide whether to receive or ignore it.
Is Lin a word?
lin n. A pool or collection of water, particularly one above or below a waterfall.
How is CAN bus load calculated?
Afaik, bus load is a percentage. bus load = #bytes send / speed. e.g. 1000 bytes (to be send in a second) * 8 (bits/byte / 500,000 (baudrate bps) * 100% = 1.6 %In your case you are sending per second: 1 / 0.005 * 50 * 76 = 760,000. 1 / 0.010 * 10 * 76 = 76,000. 1 / 0.100 * 30 * 76 = 22,800.Feb 18, 2019
What is Lin used for?
LIN (Local Interconnect Network) is a serial network protocol used for communication between components in vehicles. The need for a cheap serial network arose as the technologies and the facilities implemented in the car grew, while the CAN bus was too expensive to implement for every component in the car.
Where is the can bus located?
Typical places to pick up CAN include the ABS system (look for a pair of twisted wires, but ignore the four wheel speed wires) or on the back of the dashboard (look for a pair of twisted wires). If the vehicle does have CAN Bus on the OBD connector, it will normally be on Pins 6 and 14 as indicated below.
How does CAN bus wiring work?
CAN bus uses two dedicated wires for communication. The wires are called CAN high and CAN low. When the CAN bus is in idle mode, both lines carry 2.5V. When data bits are being transmitted, the CAN high line goes to 3.75V and the CAN low drops to 1.25V, thereby generating a 2.5V differential between the lines.